摘 要
本设计为对某发电厂的热力系统计算与通流部分管道的设计,要以最大连续蒸发量为2027t/h的锅炉及一个机组容量为600MW的汽轮机组的初始数据通过原则性热力系统的确定及计算、燃烧系统的计算及绘制,全面性热力系统的确定及计通流部分管道的设计。可行方案的选取上从实际工程项目出发,综合考虑安全可靠、经济使用,节省能源,保护环境的建设方针,同时对运行是否稳定可靠,技术是否成熟等方面进行考虑,综合比较确定。
本设计主要是对全厂的热力计算及对管道通流部分的计算及管道的选择,同时要校核相关汽水流量、进气量、发电量。根据原则性计算结果对相关热力管道进行相关基本尺寸计算,根据基本尺寸参照相关标准热力管道选型手册选择相关标准管道,并对所选管道进行相关校核计算,纠正所选管道型号,优化电厂热力系统。
最终得出电厂初步设计的相关系统确定,得出经济性较高,有建设价值的电厂建设方案。
关键词:热力系统;热经济性;管道通流部分
Abstract
The design of the power plant for the calculation of the thermal system and flow part of the pipeline design, to the maximum continuous evaporation of 2027t / h boiler and a unit capacity of 600MW steam turbine initial data through the principle of the determination of the thermal system And calculation, calculation and mapping of combustion systems, the determination of comprehensive thermal system and the design of pipelines. The choice of feasible solutions from the actual project, taking into account the safe and reliable, economical use, energy conservation, environmental protection, construction policy, while the operation is stable and reliable, the technology is mature and so on, comprehensive comparison to determine.
The design is mainly on the whole plant thermal calculation and calculation of the pipeline flow part of the pipeline and the choice of the same time to check the relevant soda water flow, intake capacity, power generation. According to the principle calculation results, the relevant basic dimensions are calculated according to the basic dimensions, and the relevant standard pipelines are selected according to the relevant standard hot pipe selection manual. The relevant pipelines are checked and checked to correct the selected pipeline model and optimize the power plant heat system.
And finally obtained the preliminary design of the power plant to determine the relevant system, come to a higher economy, the construction value of the power plant construction program.
Key words: thermal system; thermal economy; pipeline flow part
目 录
摘 要 I
Abstract II
第1章 设计概述 4
1.1汽轮机简介 4
1.2 600MW汽轮机设计的意义 4
1.3汽轮机设计要求 4
1.4设计原则 4
第2章 多级汽轮机热力计算 5
2.1设计参数的确定 5
2.2回热系统的拟定及相关参数的选择确定 6
2.3调节级的热力设计 12
2.4非调节级的热力计算 17
2.5各缸、全机功率及相对内效率 23
第3章 通流部分选型 24
3.1排汽口数和末级叶片 24
3.2配汽方式和调节级选型 24
3.3压力级设计特点 24
第4章 压力级的计算 25
4.1蒸汽信道的合理形状 25
4.2各级平均直径的确定 25
4.3级数的确定及比焓降的分配 26
第5章 整机校核及计算结果汇总 29
5.1管道计算所用相关资料 29
5.1.1推荐流速资料 29
5.1.2 相关计算公式 30
5.2具体管道管径计算 30
5.2.1主蒸汽相关管道 30
5.2.1.1 主蒸汽母管管径计算 30
5.2.1.2 主蒸汽支管(汽机进气管)计算 31
5.2.2 第一级抽汽管道内径的计算 31
5.2.3 第二级抽汽管道内径的计算 31
5.2.4 第三级高压加热器H3抽汽管道的计算 32
5.2.5 通除氧器管道的计算 32
5.2.6 低压加热器H5相关抽汽管道的计算 32
5.2.7 低压加热器H6相关抽汽管道的计算 33
5.2.8 低压加热器H7相关抽汽管道的计算 33
5.2.9 排汽管道管径的计算 33
5.2.11 锅炉给水管道支管管径的计算 34
5.3管道的选型 34
5.3.1 主蒸汽相关管道选型 35
5.3.1.1 主蒸汽母管选型 35
5.3.1.2 主蒸汽支管管选型(即:汽机进汽管) 35
5.3.2 第一级抽汽管路选型 36
5.3.3 第二级抽汽管道选型 37
5.3.4 低压加热器H3抽汽管道选型 37
5.3.5 通除氧器抽汽管道选型 38
5.3.6 低压加热器H5抽汽管道选型 39
5.3.7 低压加热器H6抽汽管道选型 39
5.3.8 低压加热器H7相关抽汽管道选型 40
5.3.9 汽机排汽管道选型 41
5.3.11 锅炉加热器给水支管管路选型 41
第6章 汽轮机的热力计算 44
6.1叶型及其选择 44
6.1.1叶型的选择 44
6.1.2相对节距和叶片数的确定 44
6.2级的热力计算 44
6.3级效率与内功率 47
总 结 49
参考文献 50
致 谢 51
附录:英文文献及翻译 52
原文 52
翻译: 66